Pixel.Mail.Ru
contact us
ru en
+7 495 249-29-39
working around-the-clock

Экокожа Орегон со скидкой 50% - купить в розницу и оптом

Экокожа НАППА ЧЕРНАЯ ширина 1,4м толщина 0,85мм

Экокожа НАППА ЧЕРНАЯ
ширина 1,4м толщина 0,85мм

на складе остался только кусок, выводим из ассортимента

данная позиция также представлена: на поролоне 3мм и 5мм со спанбондом

данная позиция также представлена: с перфорацией на поролоне 3мм со спанбондом

доступен аналог с таким же цветом: винилискожа Наппа

SUMMARY OF ECO LEATHER NAPPA:

  • roll width 1,4m, material thickness 0,85mm, manufacturer China
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • used at temperatures from -35 to +80 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$5.96 $4.18
price per lin. meter
ширина 1,4м
$3.98 $2.79
price per lin. meter
Sale in linear meters
Sale in rolls
$75.48 $52.84
price per small roll
20пог.м
$143.02 $100.11
price per roll
40пог.м
Экокожа НАППА ЧЕРНАЯ с перфорацией на поролоне 3мм (ТРИ!!!) со спанбондом ширина 1,4м

Экокожа с перфорацией на поролоне 3мм
(ТРИ!!!) со спанбондом НАППА ЧЕРНАЯ ширина 1,4м

на складе остался только кусок, выводим из ассортимента

данная позиция также представлена: без перфорации, без поролона

данная позиция также представлена: без перфорации на поролоне 5мм со спанбондом

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Экокожа на поролоне 5мм со спанбондом НАППА ЧЕРНАЯ ширина 1,4м

Экокожа на поролоне 5мм
со спанбондом НАППА ЧЕРНАЯ ширина 1,4м

на складе остался только кусок, выводим из ассортимента

данная позиция также представлена: без поролона

данная позиция также представлена: на поролоне 3мм со спанбондом

данная позиция также представлена: с перфорацией на поролоне 3мм со спанбондом

доступен аналог с таким же цветом: винилискожа Наппа

SUMMARY OF ECO LEATHER NAPPA ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $6.62
price per lin. meter
ширина 1,4м
$6.31 $4.42
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $83.81
price per small roll
20пог.м
$226.85 $158.8
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM GOLD GLITTER width 1,4m

Eco leather on foam rubber 3mm (THREE!)
and spunbond GOLD GLITTER width 1,4m

available 5,2 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber and spunbond 5mm

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM GOLD GLITTER width 1,4m

Eco leather SLIM on foam rubber 5mm
and spunbond GOLD GLITTER width 1,4m

available 16,5 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber and spunbond 3mm

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM LIGHT SILVER GLITTER width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond SILVER GLITTER width 1,4m

available 9,7 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM SILVER GLITTER width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond SILVER GLITTER width 1,4m

only pieces are available, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: without foam rubber on glue

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM YELLOW width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond YELLOW width 1,4m

available 37 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM YELLOW width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond YELLOW width 1,4m

available 7,5 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber with spunbond 3mm

this item is also available: with perforation on foam rubber with spunbond 3mm and 5mm

this item is also available: with perforation without foam rubber

this item is also available: without foam rubber on glue

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather Oregon SLIM YELLOW with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 3mm
(THREE!) and spunbond YELLOW width 1,4m

available 39,3 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Eco leather Oregon SLIM YELLOW with perforation on foam rubber 5mm and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 5mm
and spunbond YELLOW width 1,4m

available 10,3 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 3mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

this item is also available: without perforation and without foam rubber on glue

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$10.48 $5.25
price per lin. meter
ширина 1,4м
$6.99 $3.5
price per lin. meter
Sale in linear meters
Sale in rolls
$132.74 $66.37
price per small roll
20пог.м
$251.51 $125.76
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM ORANGE width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond ORANGE width 1,4m

available 33,2 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather Oregon SLIM ORANGE with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 3mm
(THREE!) and spunbond ORANGE width 1,4m

available 40,5 lin.m, withdraw from the assortment

the shade may differ slightly from orange eco leather without perforation

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon STRONG ORANGE width 1,4m

Eco leather Oregon STRONG on foam rubber 3mm (THREE!)
and spunbond ORANGE width 1,4m

available 60,2 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 1mm
  • backing - spunbond, manufacturer China
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • used at temperatures from -35 to +80 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$10.07 $5.05
price per lin. meter
ширина 1,4м
$6.72 $3.36
price per lin. meter
Sale in linear meters
Sale in rolls
$127.54 $63.77
price per small roll
20пог.м
$241.65 $120.83
price per roll
40пог.м
Eco leather Oregon STRONG ORANGE with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon STRONG with perforation on foam rubber
3mm (THREE!) and spunbond ORANGE width 1,4m

available 36,6 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 1mm
  • backing - spunbond, manufacturer China
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • used at temperatures from -35 to +80 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$11.1 $5.55
price per lin. meter
ширина 1,4м
$7.4 $3.7
price per lin. meter
Sale in linear meters
Sale in rolls
$140.55 $70.28
price per small roll
20пог.м
$266.31 $133.16
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM RED GLITTER width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond RED GLITTER width 1,4m

available 23,5 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM RED GLITTER width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond RED GLITTER width 1,4m

available 26,9 lin.m, withdraw from the assortment

this item is also available: without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM DARK RED width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond DARK RED width 1,4m

available 40 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather Oregon SLIM on foam rubber 5mm and spunbond DARK RED width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond DARK RED width 1,4m

available 57,6 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 3mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather Oregon SLIM DARK RED with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 3mm
(THREE!) and spunbond DARK RED width 1,4m

available 39,4 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Eco leather Oregon SLIM DARK RED with perforation on foam rubber 5mm and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 5mm
and spunbond DARK RED width 1,4m

available 34 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 3mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$10.48 $5.25
price per lin. meter
ширина 1,4м
$6.99 $3.5
price per lin. meter
Sale in linear meters
Sale in rolls
$132.74 $66.37
price per small roll
20пог.м
$251.51 $125.76
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM BURGUNDY width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond BURGUNDY width 1,4m

available 28,9 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather Oregon SLIM BURGUNDY with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 3mm
(THREE!) and spunbond BURGUNDY width 1,4m

available 33,1 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM LIGHT CHOCOLATE width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond LIGHT CHOCOLATE width 1,4m

available 70,1 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM LIGHT GREEN width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond LIGHT GREEN width 1,4m

available 44,7 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM LIGHT GREEN width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond LIGHT GREEN width 1,4m

available 44,8 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber with spunbond 3mm

this item is also available: with perforation on foam rubber with spunbond 5mm

this item is also available: with perforation without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather Oregon SLIM LIGHT GREEN with perforation on foam rubber 5mm and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 5mm
and spunbond LIGHT GREEN width 1,4m

available 17,7 lin.m, withdraw from the assortment

this item is also available: without foam rubber/a>

this item is also available: on foam rubber with spunbond 3mm

this item is also available: without perforation on foam rubber with spunbond 3mm and 5mm

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$10.48 $5.25
price per lin. meter
ширина 1,4м
$6.99 $3.5
price per lin. meter
Sale in linear meters
Sale in rolls
$132.74 $66.37
price per small roll
20пог.м
$251.51 $125.76
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM GREEN width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond GREEN width 1,4m

available 34,7 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: with perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: with perforation without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM GREEN width 1,4m

Eco leather SLIM on foam rubber 5mm
and spunbond GREEN width 1,4m

available 31,3 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber and spunbond 3mm

this item is also available: with perforation on foam rubber and spunbond 3mm and 5mm

this item is also available: with perforation without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather Oregon SLIM GREEN with perforation on foam rubber 3mm (THREE!) and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 3mm
(THREE!) and spunbond GREEN width 1,4m

available 39,3 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

this item is also available: without perforation on foam rubber 3mm and 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.66 $4.84
price per lin. meter
ширина 1,4м
$6.44 $3.22
price per lin. meter
Sale in linear meters
Sale in rolls
$122.33 $61.17
price per small roll
20пог.м
$231.79 $115.9
price per roll
40пог.м
Eco leather Oregon SLIM GREEN with perforation on foam rubber 5mm and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 5mm
and spunbond GREEN width 1,4m

available 31,9 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: with perforation on foam rubber with spunbond 3mm and 5mm

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$10.48 $5.25
price per lin. meter
ширина 1,4м
$6.99 $3.5
price per lin. meter
Sale in linear meters
Sale in rolls
$132.74 $66.37
price per small roll
20пог.м
$251.51 $125.76
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM DARK GREEN width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond DARK GREEN width 1,4m

available 33,5 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: with perforation on foam rubber 5mm and spunbond

this item is also available: with perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather Oregon SLIM DARK GREEN with perforation on foam rubber 5mm and spunbond width 1,4m

Eco leather Oregon SLIM with perforation on foam rubber 5mm
and spunbond DARK GREEN width 1,4m

available 36,7 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: without perforation on foam rubber 5mm and spunbond

this item is also available: without perforation, without foam rubber

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$10.48 $5.25
price per lin. meter
ширина 1,4м
$6.99 $3.5
price per lin. meter
Sale in linear meters
Sale in rolls
$132.74 $66.37
price per small roll
20пог.м
$251.51 $125.76
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM MENTHOL width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond MENTHOL width 1,4m

available 21 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 3mm (THREE!) and spunbond Oregon SLIM BLUE width 1,4m

Eco leather Oregon SLIM on foam rubber 3mm (THREE!)
and spunbond BLUE width 1,4m

available 30,2 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber 5mm and spunbond

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING:

  • roll width 1,4m, foam rubber thickness with backing 3mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$8.64 $4.32
price per lin. meter
ширина 1,4м
$5.76 $2.88
price per lin. meter
Sale in linear meters
Sale in rolls
$109.32 $54.66
price per small roll
20пог.м
$207.13 $103.57
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM SKY BLUE width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond SKY BLUE width 1,4m

available 48,5 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: on foam rubber with spunbond 3mm

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м
$6.31 $3.16
price per lin. meter
Sale in linear meters
Sale in rolls
$119.73 $59.87
price per small roll
20пог.м
$226.85 $113.43
price per roll
40пог.м
Eco leather on foam rubber 5mm and spunbond Oregon SLIM DARK TURQUOISE width 1,4m

Eco leather Oregon SLIM on foam rubber 5mm
and spunbond DARK TURQUOISE width 1,4m

available 34,6 lin.m, withdraw from the assortment

this item is also available: without foam rubber

this item is also available: with perforation

this item is also available: with perforation without foam rubber

this item is also available: without foam rubber on glue

SUMMARY OF ECO LEATHER OREGON ON FOAM RUBBER WITH A BACKING:

  • roll width 1,4m, foam rubber thickness with backing 5mm, leather thickness 0,85mm
  • backing - spunbond
  • for convenience we cut rolls of 20 lin.m or 28 sq.m
  • factory rolls are 40 lin.m or 56 sq.m
  • eco leather made in China, foam rubber and spunbond made in Russia
  • triplication made in Russia by glue method
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING DESCRIPTION:

  • Eco leather Oregon on foam rubber with backing - is eco leather Oregon, duplicated with foam rubber with a spunbond or mesh backing. It is used for sewing car seat covers, decorative upholstering of parts and seats of cars interiors, minibuses, buses, boats and details of cabins of various special equipment. Also eco leather on foam rubber with a backing is used for upholstery furniture, sports equipment, sewing toys, making haberdashery products.
  • Eco leather on foam rubber with a backing stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction. This is more than enough for sewing car seat covers and upholstering not very curved surfaces.
  • The main plus of eco leather on foam rubber with a backing is that when any surface is covered, all irregularities are smoothed out and the surface becomes soft to the touch.
  • If you need to hide irregularities and make the surface soft, and nothing suits you from the range of Oregon eco leather on foam rubber with a backing, then you can choose any eco leather from our assortment and order separately foam rubber 3mm, 5mm or 10mm thick. This foam rubber can be simply laid with the first layer under the eco leather of your choice, or glued to it using, for example, aerosol glue Fensol 60 Fentac Adhesives.
  • The foam rubber is reinforced with a backbone in the form of a spunbond or mesh, which, in addition to preventing the destruction of the foam rubber and reinforcing it, also does not allow the glue to be absorbed into the foam rubber when gluing eco leather on foam rubber, and therefore helps to stick it to the work surface with a minimum glue consumption.
  • Nice to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Air and vapor permeable.
  • It is hygroscopic, i.e. it absorbs water vapor.
  • Non-allergenic, since it does not emit anything from itself during operation.

ECO LEATHER OREGON ON FOAM RUBBER WITH BACKING USAGE:

  • Eco leather Oregon on foam rubber is used in non-professional tuning as an inexpensive upholstery leather.
  • It is mainly used for sewing seat covers and hauling door cards for car interiors.
  • It is also possible to use it for upholstery parts of a car interior, in particular, for steering wheel, a gear knob, podiums, an acoustic shelf.
  • It is used for upholstery cabins of a minibuses, buses or in the cab of trucks and various special equipment.
  • It is used for upholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • Sports equipment upholstery.
  • Padding of furniture.
  • Sewing toys.

UPHOLSTERY METHODS WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

  • The front side of the detail is covered with eco leather on foam rubber with a bend on the inside. From the inside, eco leather on foam rubber is attached with a stapler.
  • A cover is sewn according to the shape of the detail. The finished cover is pulled over the detail and pulled together from the inside of the detail with rubber bands or ropes.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using aerosol glue.
  • Eco leather on foam rubber with a backing is glued to the surface of the detail using liquid glue.

GLUES FOR ECO LEATHER ON FOAM RUBBER WITH BACKING:

HOW TO GLUE ECO LEATHER ON FOAM RUBBER WITH BACKING CORRECTLY:

  • All the methods that are given below refer to the gluing of eco leather on foam rubber with a backing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING IS DIFFERENT:
    • If you chose liquid glue Furniture, 88 or Molecule Heat Resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press eco letaher on foam rubber with backing to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco letaher on foam rubber with backing. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the eco leather on foam rubber with backing, wait until the solvent partially disappears from the adhesive, then press the eco leather on foam backing to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco leather on foam rubber is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of eco leather on foam rubber. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco leather on foam rubber (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco leather on foam rubber does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on eco leather on foam rubber is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press eco leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco leather on foam rubber, or heat the eco leather on the front side. In difficult places eco leather on foam rubber is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of eco leather on foam rubber with backing, gain some experience, and then go to the rest. The essence of gluing eco leather on foam rubber with backing is that the glue is slightly absorbed into the eco leathers foam rubber backing and on the working surface, then, after pressing the eco leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO LEATHER ON FOAM RUBBER WITH BACKING CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER ON FOAM RUBBER WITH BACKING:

NEEDED FOR RESALE ECO LEATHER ON FOAM RUBBER WITH BACKING:

$9.46 $4.73
price per lin. meter
ширина 1,4м