Pixel.Mail.Ru
contact us
ru en
+7 495 249-29-39
working around-the-clock

Eco microfiber leather Dakota - buy online

Eco microfiber leather Dakota R 2101 BLACK thickness 1.5mm width 1.4m

Eco microfiber leather Dakota R 2101
BLACK thickness 1.5mm width 1.4m

available in stock

imported as a replacementDakota D 2101

this is a new version of D 2101 with a more detailed face and an improved base

this position is also available with perforation

this position is also available as perforation ROMB

analog without microfiber is available: eco-leather Companion Dakota R 2101

all microfiber eco leather IN BLACK COLOR

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$31.37
price per lin. meter
width 1,4m
$25.9
price per lin. meter
Sale in linear meters
Sale in rolls
$376.72
price per small roll
15lin. m
$730.11
price per roll
30lin.m
Eco leather Companion Dakota RK 2101 BLACK width 1,4m thickness 1,4mm

Eco leather Companion Dakota RK 2101
BLACK width 1,4m thickness 1,4mm

available in stock

analog available: eco microfiber leather Dakota R 2101

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
15пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2101 BLACK thickness 1.5mm width 1.4m

Eco microfiber leather Dakota D 2101
BLACK thickness 1.5mm width 1.4m

available in stock

in stock 92.8, we are selling the leftovers due to the replacement withDakota R 2101

this item is also available perforated

this position is also available: on foam 3mm

analog without microfiber is available: eco-leather Companion Dakota 2101

all microfiber eco leather IN BLACK COLOR

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$31.37
price per lin. meter
width 1,4m
$25.9
price per lin. meter
Sale in linear meters
Sale in rolls
$376.72
price per small roll
15lin. m
$730.11
price per roll
30lin.m
Eco leather Companion Dakota DK 2101 BLACK width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 2101
BLACK width 1,4m thickness 1,4mm

available in stock

analog available: eco microfiber leather Dakota D 2101

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather FOR STEERING WHEEL Dakota SW-D 01 BLACK thickness 1.35mm width 1.4m

Eco microfiber leather FOR STEERING WHEEL Dakota SW-D 01
BLACK thickness 1.35mm width 1.4m

available in stock

externally differs from Dakota D 2101 only in thickness

specially designed for steering wheels; face-side film is designed for
use under stress; anti-sweat additive added

this item is also available with false perforation

all microfiber eco leather IN BLACK COLOR

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.35mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70°C
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$46.44
price per lin. meter
ширина 1,4м
$38.22
price per lin. meter
Sale in linear meters
Sale in rolls
$556.1
price per small roll
15пог.м
$1077.79
price per roll
30пог.м
Eco microfiber leather Dakota NEW BLACK thickness 1,4mm width 1,38m

Eco microfiber leather Dakota NEW
BLACK thickness 1,4mm width 1,38m

available in stock, the price has been reduced for a special offer from SHYMKA.RU

this item is also available: with perforation

this item is also available: on foam rubber 3mm and 5mm

this item is also available: with perforation on foam rubber 3mm and 5mm

all microfiber eco leather IN BLACK COLOR

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.4mm, roll width 1.38m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 18 lin.m or 24.84 sq.m
  • factory rolls are in 36 lin.m or 49.68 sq.m
  • used at temperatures from -35 to +70 °С
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$27.27 $23.18
price per lin. meter
width 1,38m
$23.16 $19.69
price per lin. meter
Sale in linear meters
Sale in rolls
$404.22 $343.59
price per small roll
15lin. m
$783.43 $665.92
price per roll
40пог.м
Eco microfiber leather Dakota NEW BLACK on foam rubber 5mm on spunbond thickness 6,4mm width 1,38m

Eco microfiber leather Dakota NEW BLACK
on foam 5mm on spunbond thick. 6,4mm width 1,38m

available 23,6 lin.m, we sell the leftovers before the new arrival

this item is also available: with perforation

this item is also available: without foam rubber

this item is also available: without foam rubber

analog without microfiber available: eco leather Companion Dakota 2101

all microfiber eco leather IN BLACK COLOR

SUMMARY OF ECO MICROFIBER LEATHER DAKOTA ON 5mm FOAM:

  • roll width 1.38m, foam rubber with 5mm backing, leather 1.4mm
  • composition: polyester 50%, polyurethane 50%
  • in a roll of 20 lin.m or 27.6 sq.m, made in China
  • eco leather made in China, foam rubber and spunbond in Russia
  • triplet made in Russia by glue method
  • used at temperatures from -35 to +70 °С
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$27.27
price per lin. meter
ширина 1,38м
$439.87
price per roll
20пог.м
$23.16
price per lin. meter
Eco microfiber leather Dakota D 2165 GRAPHITE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2165
GRAPHITE width 1,4m thickness 1,5mm

available in stock

the same item with perforation is available: Dakota PD 2165

the analog of the same color is available: Nappa N 2165

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2167 ANTHRACITE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2167
ANTHRACITE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2167

the analog is available: eco leather Partner Dakota 2167

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco leather Companion DK 2167 ANTHRACITE width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 2167
ANTHRACITE width 1,4m thickness 1,4mm

not available, arrival is expected at the end of April

analog available: eco microfiber leather Dakota D 2167

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2119 KHAKI width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2119
KHAKI width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2119

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2155 DARK GREY width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2155
DARK GREY width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2155

the analog of the same color is available: Nappa N 2155

the analog is available: eco leather Partner Dakota 2155

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2149 DARK GREY width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2149
DARK GREY width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2149

the analog is available: eco leather Partner Dakota 2149

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco leather Companion DK 2149 DARK-GREY width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 2149
DARK-GREY width 1,4m thickness 1,4mm

not available, arrival date unknown

analog available: eco microfiber leather Dakota D 2149

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2135 GREY width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2135
GREY width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2135

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2154  LIGHT GREY width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2154
LIGHT GREY width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2154

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2134  LIGHT GREY width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2134
LIGHT GREY width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2134

the analogs of the same color is available: Nappa N 2134

the analog is available: eco leather Partner Dakota 2134

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2168 LIGHT CREAM width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2168
LIGHT CREAM width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2168

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2146 CREAM width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2146
CREAM width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2146

the analog is available: eco leather Partner Dakota 2146

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Экокожа CREAM Dakota DK 2146 BROWN width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 2146
CREAM width 1,4m thickness 1,4mm

available 22,8 lin.m, arrival date unknown

analog available: eco microfiber leather Dakota D 2146

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2116 BRIGHT BEIGE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2116
BRIGHT BEIGE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2116

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 117 BEIGE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 117
BEIGE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 117

the analog is available: eco leather Partner Dakota 117

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco leather Companion DK 117 LIGHT-BEIGE width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 117
LIGHT-BEIGE width 1,4m thickness 1,4mm

only pieces available, arrival date unknown

analog available: eco microfiber leather Dakota D 117

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2169 DARK BEIGE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2169
DARK BEIGE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2169

the analog of the same color is available: Nappa N 2169

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2151 SAND width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2151
SAND width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2151

the analog is available: eco leather Partner Dakota 2151

 

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco leather Companion DK 2151 SAND width 1,4m thickness 1,4mm

Eco leather Companion Dakota DK 2151
SAND width 1,4m thickness 1,4mm

only 1 piece available, arrival date unknown

analog available: eco microfiber leather Dakota D 2151

SUMMARY OF ECO LEATHER COMPANION:

  • roll width 1,4m, material thickness 1,4mm, manufacturer China
  • composition: cotton 30%, polyurethane 70%
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +55 °С
  • sold for a cut in linear meters in multiples of 10cm and in rolls; minimum order 1 linear meter; the material you ordered is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

SPECIFICATIONS OF ECO LEATHER COMPANION:

  • composition: cotton 30%, polyurethane 70%
  • abrasion resistance: more than 500,000 (five hundred thousand) cycles (BS 5690 Martindale test)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation: 300000-500000 (three hundred - five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 1000 (one thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 54 ml/cm2. per hour (GOST 938.18-70)
  • vapor permeability: 1.3 mg/sq. cm. per hour (GOST 22900)
  • hygroscopicity: 6.0% (GOST 8971-78)
  • hypoallergenic

DESCRIPTION OF ECO LEATHER:

  • Eco leather - artificial leather, which is a thin polyurethane film reinforced with a layer of polyurethane foam with a knitted backing.
  • Eco leather stretches slightly in the transverse direction and practically does not stretch in the longitudinal direction.
  • If you need to hide irregularities and make the surface soft, then you need to order Eco leather or already triplated with foam rubber spunbond, or additionally use the first layer foam rubber of the required thickness.
  • Eco leather is pleasant to the touch - soft, elastic. Its thermal conductivity properties are close to wood, leather, it is "warm".
  • Eco leather is breathable and breathable.
  • Eco leather is hygroscopic, that is, it absorbs water vapour.
  • Eco leather is non-allergenic, because does not stand out from itself during operation.

WHAT IS THE ECO LEATHER DIFFERENT BETWEEN:

  • All Eco leathers presented on our website are of very good quality and are used in different areas. The more expensive Eco leather is, the better it is. We suggest you first purchase catalogs with samples of Eco leather you need with a 40% discount, choose the most suitable Eco leather in color, texture and quality, and then place an order on it.
  • Eco leather Oregon - the cheapest and most bought position from eco leather! Despite the price, Oregon Eco leather has good wear resistance, and in appearance is not inferior to expensive counterparts.
  • Space and Vega Eco leather - a novelty in the range of Eco leather for furniture. Similar in quality to Oregon faux leather.
  • Eco leather Alba and Art Vision - high-quality Eco leather for furniture, which is also widely used in auto-tuning. The unique finish gives the material additional qualities that expand its design possibilities. Eco leather with good hygienic and performance properties, providing maximum comfort. The material is lightfast, breathable, highly resistant to repeated bending, abrasion and scratch resistance. It is used for sewing car covers and car seats.
  • Eco leather Cordoba is a new high-tech type of Eco leather. Like any other Eco leather, this material in its appearance and tactile properties is as close as possible to natural leather. The main feature of Eco leather Cordova is the special EASY CLEAN coating, which provides easy cleaning from most household dirt, including traces of ballpoint pens. To remove ink, simply rub the skin with a regular paper towel. That is why Eco leather Cordova is perfect for upholstering furniture, upholstering a car interior and sewing high-quality car seat covers. In terms of its performance characteristics, Eco leather Cordova is noticeably superior to Eco leather Oregon, but still inferior in strength Eco leather on microfiber.
  • Eco leather Crete - high-tech artificial leather with increased wear resistance: up to 200,000 Martindale test cycles. This is several times more than that of budget Eco leather and, in fact, in terms of wear resistance, it corresponds to Eco leather on microfiber. Topics no less Eco leather Crete does not have a microfiber backing, so it is not so resistant to cuts and mechanical damage. Scope of Eco leather Crete: upholstery of car interiors, home, industrial and public furniture.
  • Eco leather Companion differs from Eco leather Oregon, Alba and Art Vision in a more wear-resistant and durable polyurethane film in the front layer, which is super scratch resistant. Eco leather Companion has the same front layer as Eco Microfiber leather, but differs in that the polyurethane film is applied not on microfiber, but on polyurethane foam with a fleece fabric backing. If the Eco Microfiber leather is used for the complete constriction of the car interior seats, then the Eco leather Companion is mainly used for upholstery of the seat backs, for sewing covers and the constriction of not very curved parts of the car interior.
  • Eco leather Stretch is distinguished by its softness and plasticity, which allows it to be used when sewing outerwear - jackets, raincoats, and also suits, skirts, trousers. It is also widely used for sewing handbags and accessories.
  • Of the entire range of faux leather, only eco leather Oregon and eco microfiber leather are available in perforated versions.

ECO LEATHER APPLICATION:

  • Eco leather is mainly used for sewing seat covers and upholstery for passenger cars, minibuses, buses, truck seats and various special equipment.
  • It is used for binding door cards, gear lever, podium, acoustic shelf, car interior panel elements.
  • Attention, in 90% of cases, tuning studio masters use Eco Microfiber leather for professional upholstery of seats and door cards of the car interior. It has the same thickness as genuine leather in skins, and the quality and variety of colors and textures of Eco Microfiber leather are unmatched!
  • If you need to upholstery the steering wheel or gear stick, we recommend using the SW for steering wheels series. Eco microfiber leather Schweitzer BMW, Schweitzer Nappa and Dakota many craftsmen also use the steering wheel and gearshift knob to tighten, but on their own responsibility.
  • It is used for covering various skins in the cabin of a minibus, bus, in the cab of trucks and various special equipment.
  • Upholstery of furniture for the home.
  • Upholstery of office furniture.
  • Upholstery of children's furniture.
  • Upholstery of sports equipment.
  • Sewing toys.
  • Sewing handbags.

RECOMMENDATIONS FOR CAR SEATS UPHOLSTERY WITH ECO LEATHER:

  • Under any Eco leather it is necessary to putfoam rubber on a backing, which is desirable to stick to Eco leather when tightening the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac Adhesives or Tuskbond.
  • Which foam to use, mesh or spunbond? Experts in the field of car seat upholstery recommend using foam rubber on a mesh, which is more durable than spunbond.
  • Eco leather for the middle inserts of the back and seat, as a rule, is duplicated with foam rubber on a 10mm mesh, and the side support elements of the back and seat - with foam rubber on a 5mm mesh.
  • For your convenience, the range of Eco leather on our website contains Eco leather Oregon on foam rubber with a backing. Foam rubber with a backing in the form of a mesh or spunbond is already glued to the Oregon Eco leather by the glue method, which allows you to immediately use the sandwich when tightening, and not stick the foam to the Eco leather.

WAYS OF FITTING ECO LEATHER DETAILS:

  • The front of the part is covered with eco leather with a fold on the inside. From the inside, the eco leather is attached with a stapler. If necessary, foam rubber of the required thickness is laid under it.
  • A cover is sewn from eco leather according to the shape of the part. The finished cover is pulled over the part and pulled together from the inside of the part with rubber bands or ropes.
  • eco leather is glued to the surface of the part using aerosol glue.
  • eco leather is glued to the surface of the part with liquid glue.

GLUES SUITABLE FOR ECO LEATHER:

HOW IS IT CORRECT TO PUT ON ECO LEATHER:

  • All the methods below are for the eco leather gluing.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • DEPENDING ON THE ADHESIVE, THE METHOD OF GLUING DIFFERENT:
    • If you have chosen liquid glue Furniture, 88 or Molecule Heat Resistant, then it is necessary to apply the glue in a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially evaporates from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. The final bonding with these liquid adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well.
    • If you have chosen one of the aerosol adhesives (the most common method), then you need to spray the glue on the work surface and on the inside of the eco leather, wait until the solvent partially disappears from the glue, after which it is necessary to press the eco leather to the surface and fix it for a short time. Final bonding with aerosol adhesives takes place within 24 hours. You can not apply glue to the eco leather itself, if it already adheres well. Attention, with a 100% guarantee, eco leather will only be glued to the working surface with Scotch-Weld 3M 90. The rest of the aerosol adhesives given above are also used for gluing eco leather, but, for some reason, there are sometimes complaints about them. It's up to you.
    • If you have chosen thermoactivated glue Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, If you have chosen thermoactivated glue , then gluing eco leather is much more difficult with a industrial hairdryer. The glue is applied to both glued surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer with a brush (roller). The glue is applied to both bonded surfaces evenly, without gaps. Avoid strong glue soaking the inside of the eco leather. From a spray gun, glue is applied in at least five thin layers. Each subsequent layer is applied after the previous layer has dried. Drying time for each layer is 20-30 minutes. After the last layer has dried, eco leather (with an adhesive layer applied to it) is laid on the working surface (casing), which, in turn, is also covered with an adhesive layer. Since the glue on the work surface and on eco leather after drying does not possess stickiness, the two surfaces do not stick together when applied to each other. This is very convenient, as it allows you to lay out eco leather with an adhesive layer applied to it on a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the eco leather is decomposed, the glue on the work surface and on the eco leather is activated (heated) in small areas with an industrial (professional) hairdryer until stickiness appears, after which the eco leather is smoothed and pressed against the work surface. You need to press the eco leather until the temperature of the glue drops and both surfaces stick together. To activate the glue, you need to either directly heat the glue from the wrong side of the eco leather, or heat the eco leather itself from the front side. eco leather in difficult places is additionally warmed up with a hairdryer. Thus, section by section, gluing takes place over the entire surface. This is the convenience of step-by-step gluing of eco leather using thermoactivated glue. The distance from the hair dryer nozzle to the adhesive layer and the temperature are chosen so as not to burn the eco leather and at the same time activate (liquefy) the adhesive. Wear protective gloves to avoid burns. Special places subject to stress are additionally glue-treated. When glue is applied in thin layers, the glue does not give thickness. If you find a non-glued area, the glue allows you to fix this defect by reheating the area.
  • We recommend that you try to stick a small piece of eco leather first, gain some experience, and then move on to the rest of the material. The essence of gluing eco leather is that the glue is slightly absorbed into the substrate and into the work surface, then, after pressing the eco leather to the work surface, the two surfaces are firmly glued. Before gluing, carefully read the instructions for using the appropriate adhesive on our website in the glues. section.

ECO LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO LEATHER:

NEEDED FOR RESALE ECO LEATHER:

$17.68
price per lin. meter
ширина 1,4м
$14.25
price per lin. meter
Sale in linear meters
Sale in rolls
$203.02
price per small roll
20пог.м
$384.66
price per roll
30пог.м
Eco microfiber leather Dakota D 2140 GREY BEIGE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2140
GREY BEIGE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2140

the analog is available: eco leather Partner Dakota 2140

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2106 BLUE width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2106
BLUE width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2106

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 2181 BRIGHT RED width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 2181
BRIGHT RED width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 2181

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 119 RED width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 119
RED width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 119

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, after pressing the eco-leather to the working surface, two surfaces are firmly bonded. Before the gluing, carefully read the instructions for using the appropriate glue on our website in the section glue.

ECO MICROFIBER LEATHER CARE:

  • NO DRY CLEANING for eco leather! It will start to peel off immediately after dry cleaning or a little later. The front polyurethane layer is destroyed by dry cleaning. Dry cleaning also breaks the bond of the front polyurethane layer with the base.
  • To remove common pollutions (tea, coffee, juice, dust, etc.), the eco leather surface must be treated with a moistened soft cloth with light movements, then be sure to wipe it dry. In the same way dust and dirt are removed. If it was not possible to get rid of the pollution immediately, the use of 40-50% alcohol-water solution or ammonia is allowed.
  • Over time, leather upholstery, when exposed to sunlight, humidity, temperature, and other effects, dries out, loses its elasticity and appearance, wipes, stretches, or begins to tear at the seams, and cracks form on the surface of the leather that become clogged with dirt. To avoid such troubles and to preserve the integrity of eco leather as long as possible, it is necessary to use a special tool for eco leather care - conditioner for eco leather. It is necessary to process eco leather with such a tool once a month in the summer and once every three months in the winter.
  • If the surface is covered with snow-white eco leather or eco leather of light tones, then for better protection from pollution (for example, jeans can “tint” the leather upholstery of the furniture with a dye that cannot be removed), it is recommended to use special water and dirt-repellent impregnations for eco leather, textiles and high-tech materials. These funds can be purchased at almost any supermarket, in stores selling shoes and leather clothes. When choosing an impregnation, be sure to read the instructions for use. If there is an indication "not use for PU" (do not use for polyurethane coatings), then this product is not suitable.
  • It is strongly discouraged to leave the eco leather wet after the care and cleaning procedures. This will lead to a partial destruction of the polymer film, and, as a consequence, to premature loss of the original appearance of eco leather.
  • Today more and more eco leather in the car interior is wiped with wet wipes. This can never be done! The composition of the solution with which the wipes are moistened includes components that destroy eco leather. It is enough to wipe the eco leather with a soft cloth moistened with clean water.
  • Attention! Do not use solvents and abrasive cleaners to clean eco leather !!!

NECESSARY FOR UPHOLSTERY WITH ECO MICROFIBER LEATHER:

NEEDED FOR RESALE ECO MICROFIBER LEATHER:

$32.74
price per lin. meter
width 1,4m
$27.27
price per lin. meter
Sale in linear meters
Sale in rolls
$396.65
price per small roll
15lin. m
$768.74
price per roll
30lin.m
Eco microfiber leather Dakota D 116 HAZEL width 1,4m thickness 1,5mm

Eco microfiber leather Dakota D 116
HAZEL width 1,4m thickness 1,5mm

available in stock

the same item is available with perforation: Dakota PD 116

the analog is available: eco leather Partner Dakota 116

SUMMARY OF ECO MICROFIBER LEATHER:

  • material thickness 1.5mm, roll width 1.4m
  • composition: polyester 50%, polyurethane 50%, manufacturer China
  • for convenience we cut rolls of 15 lin.m or 21 sq.m
  • factory rolls are 30 lin.m or 42 sq.m
  • used at temperatures from -35 to +70 °C
  • abrasion resistance:
    220,000 (two hundred twenty thousand) cycles (test BS 5690 Martindale)
  • resistance to repeated bending after exposure to moisture and ultraviolet radiation:
    500,000 (five hundred thousand) cycles (GOST 8979-75 artificial aging)
  • abrasion resistance: 3000 (three thousand) revolutions (TsNIIPIK method)
  • frost resistance: 50,000 (fifty thousand) cycles (GOST 20876-75)
  • color fastness to light: 4 points (good) (ASTM D-3597 test)
  • cigarette test - non-flammable (passed ISO 8191/188)
  • breathability: 2.5-3 ml / sq. Cm. per hour (GOST 938.18-70)
  • vapor permeability: 1.6 mg / cm 2 per hour (GOST 22900)
  • hygroscopicity: 3.5% (GOST 8971-78)
  • hypoallergenic
  • sold for a cut in linear meters in multiples of 10 cm and in rolls; minimum order 0.5 lin.m; the ordered material is wound on a round tube before shipment and carefully packed in several layers of air-bubble film

MICROFIBER ECO LEATHER DESCRIPTION:

  • Microfiber eco leather - artificial leather, which is a thin high-strength polyurethane film reinforced with high-strength microfiber. Microfiber - it's a non-woven material with a thickness of 1.1-1.5 mm and 100% consisting of refractory polyester. Microfiber consists of very small, tightly twisted tows, interlocked, forming something like a 3D chain mail.
  • Microfiber eco leather - unique automotive artificial leather. It is highly resistant to scratches and other mechanical stress. High-strength frame properties are achieved due to the fact that the microfiber, which are the basis of the material, absorb the polyurethane coating into their spatial volume, forming a single whole.
  • This is a high-tech product, the tensile strength of which exceeds all existing automotive and upholstery materials.
  • It stretches well in the transverse direction and stretches slightly in the longitudinal direction. These stretching properties ideally to use microfiber eco leather specifically for car seats reupholstery.
  • Microfiber eco-leather has three times higher durability than standard genuine automotive leather in skins. Due to its porous structure, it allows air and moisture to pass through, like natural leather, which will ensure its comfortable use in cold and hot seasons.
  • In the finished product, eco-leather on microfiber is indistinguishable from genuine leather. After a year of use, even a professional will not be able to say whether natural material was used or not. At the same time, eco-leather on microfiber is much more durable and unpretentious, it is almost impossible to accidentally cut or scratch it. It does not age and does not require any care, unlike genuine leather.
  • In contrast, for example, from bielastisch or thermo leather universal, microfiber eco leather cannot be stretched in one piece on a complex curved surface. Therefore, it is cut into parts, stitched, if necessary, duplicated with foam rubber and pulled onto the part, tightening it or putting it on glue.
  • It has a thickness of 1.1-1.5mm, which allows you to smooth out small irregularities of the tightened surface. If you need to hide large irregularities and give the surface softness, then you can order separately foam rubber on a substrate 3mm, 5mm or 10mm thick. This foam can simply be laid with the first layer under the leather, or glued to it using, for example, aerosol glue Fensol 60 Fentac.
  • Pleasant to the touch - soft, elastic. Its thermal conductivity are close to wood, natural leather, it is “warm”.
  • Air and vapor permeable. Hygroscopic, absorbs water vapor.
  • Non-allergenic, because it does not secrete anything from itself during exploitation.

MICROFIBER ECO-LEATHER ASSORTMENT:

HOW MICROFIBER ECO LEATHER DIFFER FROM EACH OTHER:

  • On our site there are a lot of different microfiber eco leathers. The more expensive it is, the more wear-resistant and better quality it have. Eco leather on microfiber is distinguished by embossing, stiffness, ductility, thickness. Characteristics are indicated in the description of each item. To study and compare all eco-leathers on microfiber, we recommend buying catalogs and try to work with different species.
  • Top selling collections - is Dakota and Schweizer BMW. Other collections are sold less, but this does not mean that they are worse.
  • If you need to drag the steering wheel or gear knob, we recommend using the series SW for wheels. Many masters also use Microfiber eco leather Schweizer BMW, Schweizer Nappa and Dakota for the steering wheel and gear knob, but at their own risk.
  • Economy class microfiber eco leather is Nova and Standart. It's not necessary to always use expensive microfiber eco leather. You can upholster saloon with a budget option. For example, the use of budget microfiber eco-leather is reasonable in the case when the car is being prepared for sale or rarely used, which does not require the use of eco-leather with high wear resistance.
  • On our website it is indicated that the thickness of almost all microfiber eco leather is 1.3-1.5mm. This thickness is obtained by adding 20 samples of any microfiber eco-leather, measuring the height of the resulting pile with a ruler and then dividing the resulting value by 20. It is not necessary to compress the samples during measurements. If you start measuring the thickness of different microfiber eco-leathers, then the thickness will go vary from 1.2 to 1.6mm. Even if you measure the same piece of microfiber eco-leather, then the thickness will also change by 0.1-0.2 mm. Therefore, the thickness of 1.3-1.5 mm indicated by most microfiber eco-leather is conditional, and there is no point in arguing on this topic. We sell the material as it really is. To familiarize yourself with all microfiber eco-leathers, we recommend that you purchase the appropriate catalogs.
  • Microfiber eco leather Dakota, Monza, Nappa, Nova come in rolls from 25 to 40 linear meters, so the conditional length of the roll is 25 lin.m. Microfiber eco leathers Schweizer, Standart, Luxe, New come in rolls 30 lin.m long. Therefore, a roll length of 30 lin.m is adopted on them. If you need to buy a roll of maximum length, then please contact with the operators via email or phone to find out which rolls are in stock.

MICROFIBER ECO LEATHER USING:

  • It is used in professional tuning as an expensive super-high-quality artificial leather.
  • In 90% of cases it is used for a professional, expensive reupholstering of car seats.
  • In particular, it is used for reupholstering the steering wheel and gear knob.
  • Microfiber eco leather can be used at any detail in the car.
  • Used for reupholstering the seats of motorcycles, ATVs, jet skis, bicycles.
  • It is used only by professional interior reupholstering masters, as it requires work skills.
  • It is used for a reupholstering of expensive furniture where high wear resistance of a covering is required.
  • It is used for reupholstering seats and furniture on boats and yachts, but during operation not in the open air and without frequent exposure to water.
  • Reupholstering of sports exercise machines.

RECOMMENDATIONS FOR REUPHOLSTERING SEATS WITH MICROFIBER ECO LEATHER:

  • When reupholstering the seats, microfiber eco leather needs to be reinforced with spunbond with a density of at least 60 g/m2 to prevent cracking of the face layer under strong stretching microfiber itself. Spunbond glues to microfiber with aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • For softness and volume, under eco-leather on microfiber (if there was reinforcement with spunbond, then with glued spunbond) also put foam rubber on the backing, which is desirable to stick to eco leather when reupholstering the seats. For these purposes, we recommend using aerosol glue Fensol 60 Fentac or Tuskbond ONE or TACK 200.
  • What foam rubber to use - on a grid or on a spunbond? Experts recommend using foam rubber on a mesh that is more durable than spunbond.
  • Microfiber eco-leather, given its thickness of 1.3-1.5mm, for medium inserts, the backs and seats are usually duplicated with foam rubber on a mesh of 7 or 10 mm thick. The lateral supporting elements of the back and seats are duplicated with foam rubber on a mesh 3 or 5 thickmm.

EXPERIMENT WITH MICROFIBER ECO LEATHER:

  • We make a small incision with a scissor on any furniture fabric, artificial leather or natural automotive leather in any direction. And quite easily tear the material with your hands. A similar attempt with microfiber eco-leather fails! You will feel the difference without any labs! These characteristics of microfiber significantly increase the life of eco-leather on microfiber.

SUITABLE GLUE FOR MICROFIBER ECO LEATHER:

HOW TO CORRECTLY APPLY MICROFIBER ECO LEATHER:

  • All methods that are listed below relate to apply microfiber eco leather.
  • First you need to measure and cut off the required piece of material. Then it should be laid out on the surface to be pasted and the course of the gluing should be planned (take into account the phasing of the gluing, all surface bends, time intervals).
  • The surfaces to be bonded must be cleaned and dried.
  • Smooth plastic surfaces should preferably be sanded with fine sandpaper (grit 100) for better adhesion to the glue.
  • The working surface must be degreased with a thinner-cleaner Moleculeor others degreasers.
  • If the working surface is plastic with PP/PE marking or other markings, before applying glue, you need to treat such a surface with anti-siliconeandprimer on plastic, so that the glue does not peel off the plastic.
  • If some old material is already installed on the work surface, then it is up to you to rip it off or not. You can stick the new material directly onto the old material. We recommend that you try sticking on a small piece and decide whether to remove the old material or not.
  • When preparing the steering wheel for upholstering, acetone cannot be used, and if it is treated with a solvent containing acetone, or etching, then it is imperative to let it brew for several hours before upholstering so that it is completely dry. If, for example, glue SAR is used, then a thinner-cleaner is absolutely necessary Molecule, not acetone. Violating these rules, at high temperatures, acetone vapors penetrate the microfiber and the top layer is destroyed.
  • DEPENDING ON THE GLUE, THE METHOD OF GLUING DIFFERS:
    • If you have chosen one of the aerosol glues, you need to spray it on the work surface and on the wrong side of the microfiber eco leather, wait until the solvent partially disappears from the adhesive, then press the microfiber eco-leather to the surface and fix it for a short time. Final gluing with aerosol adhesives occurs within 24 hours. Attention, with a 100% guarantee, microfiber eco leather can be glued to the working surface only with Scotch-Weld 3M 90. The rest of the aerosol glues given above are also used to gluing microfiber eco leather, but for some reason, there are sometimes complaints about them. You decide.
    • If you chose liquid glue Molecule heat-resistant, it is necessary to apply glue with a thin layer on both surfaces with a brush, roller or using a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), wait until the solvent partially disappears from the glue, after which it is necessary to press microfiber eco-leather to the surface and fix for a short time. Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. Final bonding with this heat-resistant glue occurs within 24 hours. You can don't apply glue to the eco-leather itself if it already adheres well.
    • If you have chosen one of the thermally activated glues Molecule Thermo Active, KLEYBERG 900-И, Poligrip, SAR 306, SAR 30-E, then gluing the eco-leather is a little more complicated, and require a hairdryer. The glue is applied to both surfaces either with a spray gun from a distance of at least 30-40 cm (nozzle diameter 2.5-3 mm, air pressure at least 4 atmospheres), or with a thin layer of a brush (roller). Glue is applied on both glued surfaces evenly, without gaps. Do not allow glue to impregnate the inside of microfiber eco-leather. The glue is applied in at least five layers. Each subsequent layer is applied after the previous layer has dried. The drying time of each layer is 20-30 minutes. After the last layer has dried, eco-leather (with an adhesive layer applied to it) is laid on the work surface, which is also covered with an adhesive layer. Since the glue on the work surface and on eco-leather does not have stickiness after drying, the two surfaces do not stick together when applied to each other. This is very convenient, since it allows you to decompose the material with the glue layer applied on it onto a working surface covered with glue and to anticipate and plan a step-by-step gluing process. After the material is decomposed, the glue on the work surface and on microfiber eco-leather is activated (heated) in small sections by an industrial (professional) hairdryer until sticky, after which the material is smoothed and pressed to the work surface. It is necessary to press microfiber eco-leather until the glue temperature drops and both surfaces stick together. To activate the glue, you must either directly heat the glue from the wrong side of the eco-leather, or heat the eco-leather on the front side. In difficult places microfiber eco-leather is additionally heated by a hairdryer. Thus, site after site, bonding occurs over the entire surface. This is the convenience of step-by-step gluing using thermally activated glue. The distance from the nozzle of the hair dryer to the adhesive layer and the temperature are selected so as not to burn eco-leather and at the same time activate (thin) the glue. To avoid burns, use a protective glove. Special places subjected to load are additionally treated with glue. When applying glue in thin layers, the glue does not give thickness. If you find a non-glued place, the glue allows you to fix this defect by re-heating this area.
  • We recommend that you try first sticking a small piece of microfiber eco-leather, gain some experience, and then go to the rest. The essence of gluing microfiber eco-leather is that the glue is slightly absorbed into the microfiber eco-leather and on the working surface, then, af